 |
|
|
|
Note
Easy-install system lets you enjoy your favorite sport in complete safety!
Quality designed and built for many years of reliable service. Meets all
Canadian safety standards.
|
|
|
 |
Care and safety
instructions
Never use petroleum-based cleaning products.
Store your RX-Jack in a dry location away from sharp objects.
The RX-Jack seat is designed specifically for recreational use.
Normal conditions of use:
Allow only one person at a time to use the RX-Jack.
Inspect your RX-Jack before each use. Ensure that all parts are properly
assembled and firmly attached to the original seat. Check that the washers are
screwed on tight. Replace any worn, defective, or missing parts.
Do not exceed the maximum weight limit of 175 lb. (79.5 kg) for the RX-Jack.
Note: We highly recommend that you see your authorized Jack dealer for proper
installation. Industries Jack cannot be held liable for risks the user may incur
by using this product. |
|
|
Installation
Note: Do not attach your Rx-Jack until the slides are properly installed.
Otherwise, you could damage or tear the seat of your snowmobile. |
|
Important
|
|
|
|
|
1
Remove the srews with a screwdriver. If it is hard to do. Skip to the step 2.
|
|
 |
|
|
|
|
|
2
Unscrew the 3 hexagonals screws as show.
Be
careful, remove only screws as show on the following three step. The two others
are fakes one.
|
|
|
|
|
|
|
3
Only screw as show.
|
|
 |
|
|
|
|
|
4
Only screw as show.
|
|
 |
|
|
|
|
5
Remove the screws holding the plastic panel. |
|
 |
|
|
|
|
6
Push from the bottom of the panel.
|
|
 |
|
|
|
|
7
With your hand remove carefully the panel by unlocking the snap under the seat.
|
|
 |
|
|
|
|
8
Push carefully the plastic trim to unsnap the bottom of the plastic panel. |
|
 |
|
|
|
|
9
Remove the plastic panel slowly, carefully and side by side as show. |
|
 |
|
|
|
|
10
Remove the screws of the plastic exhaust protector. |
|
|
|
|
|
|
11
Remove the nuts holding the seat. |
|
 |
|
|
|
|
12
Lift off the seat from the back until you see the section under the gas tank.
|
|
 |
|
|
|
|
|
13
Disconnect the rear light plug.
.
If you have skip the
first step, it's time to go back !
|
|
 |
|
|
|
|
|
14
Put the track as show.
|
|
 |
|
|
|
|
|
15
You can use only two bolts on each side. If you want to use the third one. Drill
from the bottom and insert the bolt from the bottom.
|
|
|
|
|
|
|
|
16
Replace the exhaust plastic protector and replace the seat by following the
steps 13 to 1.
Before ride
with your new Jack product, read carefully your installation guide.
|
|
 |
|
|
|
|
|
|
Warranty
The manufacturer warrants all parts against defects in material or workmanship
for one year after purchase and will repair or replace without charge any parts
that prove defective under normal conditions of use (see Care and Safety
Instructions above).
Product is exchangeable but nonrefundable.
In the event of a defect, contact your dealer to ensure it is covered by the
manufacturer’s warranty before returning the part for repair or replacement. Use
a sturdy container suitable for mailing. All return shipping and handling costs
are the responsibility of the dealer or customer.
Please enclose proof of purchase, the owner's name and address, and a written
description of the problem or defect.
This warranty replaces all other warranties, express or implied, including, but
not limited to, any implied warranty of merchantability or fitness for
particular purpose. In no event shall the manufacturer be liable for any loss of
profit or any direct, incidental, or other damage. |
|